SETTSU METAL INDUSTRIAL Racks (options, autres)

?* À propos du délai d'expédition et des prix

• 

  Support SHF, série RKP

  SETTSU METAL INDUSTRIAL

  [Features]
  · Accessory for Sub Rack RKU2 series.
  · Adjust the guide frame and connector frame up and down using the sub H frame when storing PCB with non-compatible dimensions or when installing a connector with extreme dimensions. This is a part for attaching a guide frame and connector frame to the sub H frame in this situation.
  · Tighten both sides of the guide frame C or the connector frame G with M4 panhead screws.
  · Use either the sub H, sub W or border D frame accessories to directly attach this bracket to the sub rack.

  à partir de∗ ：	15.34 €
  Délai d'expédition minimum ：	6 jours

  *Prix unitaire/configuration de base

• 

  Cadre de guidage C série RKP

  SETTSU METAL INDUSTRIAL

  [Features]
  · Accessory for Sub Rack RKU2 series.
  · A frame to mount card guide 2 (RKP-□□□CG□2).
  · This frame has a card guide mounting hole (φ4.2) at a 6.35 mm (1/4 inch) pitch.
  · One of the two ways to use this frame is to attach a GWF slide piece to both sides.
  Then there is the mounting method for the SHF bracket on each side.
  For details, refer to pieces for GWF slides (RKP-4GSA) or brackets for SHF (RKP-34BTA).

  à partir de∗ ：	23.12 €
  Délai d'expédition minimum ：	6 jours

  *Prix unitaire/configuration de base

• 

  Cadre de connecteur G série RKP

  SETTSU METAL INDUSTRIAL

  [Features]
  · Accessory for Sub Rack RKU2 series.
  · Frame for mounting edge board connectors, DIN connectors, etc.
  · φ3.2 holes drilled at 6.35 mm (1/4") pitch.
  · When the mounting position of the connector matches the center of the card guide, such as with edge board connectors, attach the spacer with the "EDGE" engraved stamp and attach SHF brackets to both ends.
  · When the mounting position of the connector is displaced from the center of the card guide by 4.35 mm to the right, such as with DIN connectors, attach the spacer with the "DIN" engraved stamp and attach SHF brackets to both ends.
  · Looking at the sub rack from the back, use either the sub H or sub W frame accessories to directly attach this frame to the sub rack., making sure the part marked "TOP" is up and "BOTTOM" is down.
  · The strongest frame among the connector frames.

  à partir de∗ ：	60.61 €
  Délai d'expédition minimum ：	6 jours

  *Prix unitaire/configuration de base

• 

  Charnière série RKP

  SETTSU METAL INDUSTRIAL

  [Features]
  · Accessory for unit cases from the RMU series.
  · A hinge used for opening and closing front panels.
  · Attach the rotor side to the front panel and the stator to the RKU series W frame.
  · Depending on how the stator is attached, two functions can be performed: vertical and horizontal opening and closing.
  · In other words, the stator must face vertically for the horizontal open/close type, while it should face horizontally for the vertical open/close type.
  · Two knob screws and E rings each are included for fixing the front panel.
  · In the left and right opening/closing type, whether it opens right or left is determined depending on whether the stator is attached to left or right.
  · The front panel of the front and rear opening and closing type is made to stop at a roughly horizontal point when completely open.

  à partir de∗ ：	38.56 €
  Délai d'expédition minimum ：	6 jours

  *Prix unitaire/configuration de base

• 

  Panneau avant A série RKP

  SETTSU METAL INDUSTRIAL

  [Features]
  · Accessory for unit cases from the RMU series.
  · I/O connectors and other operation accessories can be attached to this fixed type front panel.
  · This panel has a flat plate shape that makes drilling holes easy.
  · Naturally, it can also be used for the rear section.
  · Mount to the front and rear part of the RMU series with M3 screws.

  à partir de∗ ：	37.85 €
  Délai d'expédition minimum ：	6 jours

  *Prix unitaire/configuration de base

Loading...